IRACING MONITOR SETUPStarting values are examples
Prepare your monitor settings

Measure outer width, then use Compute in iRacing.

Measurement units
cm
cm

Measurements for iRacing

Example record ready — replace with measurements

Monitor Type
1 Flat Screen
Monitor Width (including bezel)
61.00 cm · example
Viewing Distance (center screen)
60.00 cm

Match the units shown in the simulator before entering numbers.

Final in-game FOVUse Compute in iRacing to obtain your final FOV
Physical FOV estimate

Center panel only. These angles are not the final iRacing Compute output.

52.96°
Physical horizontal FOV
31.30°
Physical vertical FOV

Physical angles are not iRacing’s Compute output.

Visible width 59.77 cm · visible height 33.62 cm

Open center-panel geometry
Measurement assumptions and source limits
  • Outer width is an example value. Replace it with an edge-to-edge measurement of your monitor.

Public support checked 2026-11-19. Installed client build and the exact native Compute algorithm have not been tested.

How to measure

Outer width: measure one monitor edge to edge, including both frames. A diagonal or visible width does not fill this field.

Eye distance: measure from between your eyes to the center screen’s surface in your normal driving posture.

One edge bezel: record one side only, not both sides combined. Frames do not add emitting image area.

Side angle: 0° means screens in one line. Use matching inward angles; this is not the angle subtended at your eyes.

Optional visible panel measurements

This helper never invents or fills outer width. Measure the housing separately.

in

Show measurement diagram
Eye pointDOuter width, including both frames1 Flat Screen · schematic, not to scaleRB: one edgeJoint angle
Gray spans include frames; green spans are visible image areas. Rays refer to the center panel only. Side shapes and radius are schematic, not calibrated hardware or a final game FOV.

Your setup checklist 0 complete

Measure from your settled eye position. Keep the visible area, complete housing width and one-edge frame measurement separate.

Verified setup references

Public documentation checked 2026-11-19; installed client build not tested. This is an independent assistant, not an iRacing product.

MEASURE THE HARDWARE. CONFIGURE THE SIMULATOR.

iRacing FOV Calculator

Use this iRacing FOV calculator to prepare the monitor measurements that belong in the simulator, then follow its native Compute workflow and check your cockpit view. Choose one or three flat or curved screens, record outer width and eye distance, and add the fields relevant to that mode. Optional physical angles describe the center panel; iRacing supplies the final in-game FOV. The starting values are examples to replace with your own measurements.

Measure the Values iRacing Asks For

A useful measurement record keeps the monitor housing, emitting panel and viewing position distinct. Sit normally after setting your seat, wheel and pedals; the wheel is a landmark rather than the eye point.

Monitor Width: Outer Edge vs Visible Panel

Measure one monitor from its outer left edge to its outer right edge, including both frames. The three-monitor support article uses this definition for Monitor Width. A marketed diagonal describes the panel and cannot reveal the casing width. Measurements arriving from another calculator leave outer width blank until you supply it.

Measure Eye Distance From Your Normal Seat Position

Use the point between your eyes and the center monitor’s front surface. The centered model uses perpendicular distance, not a tape run from the wheel, desk edge or rear casing. Recheck after moving the seat or monitor arm. An off-center or uneven triple rig needs more information than the symmetric assistant record.

Single-Edge Bezel Width and Side-Screen Angle

Bezel Width means one edge, not the sum of left and right borders. For flat triples, side angle is the inward rotation where a side monitor meets the center monitor. Zero degrees means all panels lie in one line. It is a joint angle, separate from the angle the screen occupies at your eyes.

For a concrete flat-panel example, suppose measured outer width is 61.00 cm and each horizontal edge bezel is 0.60 cm. With an explicit equal-left/right-frame assumption, visible width is 61.00 − 2 × 0.60 = 59.80 cm. This is a width derivation, not a way to turn any 27-inch marketing label into a housing measurement.

If visible height is 33.64 cm after rounding and centered eye distance is 60 cm, the shared physical engine gives 52.98° horizontal and 31.32° vertical. These use the visible area. The native record still uses the separately measured outer width and one-edge bezel. No final iRacing degree value is inferred from this example.

Enter Your Measurements in iRacing

Find Display > Monitor and Select the Right Monitor Type

The seating-position guide and beginner setup reference describe the simulator’s Settings → Display → Monitor workflow. Choose the same Monitor Type as your hardware: 1 Flat Screen, 1 Curved Screen, 3 Flat Screens or 3 Curved Screens. This assistant presents those four records; it does not offer a monitor FOV value for VR optics or IPD.

Match the unit displayed by the native field before entering a number. The cm/mm/in buttons convert the same stored lengths here. Monitor width is one panel’s outer width; triple mode does not mean entering three widths as one giant monitor. Follow the installed tooltips if the interface differs from the public documentation.

When to Click Compute

Enter the required measurements first, then use Compute in the native Field of View Calculator. The measurement summary is a preparation record, and the physical estimate is a geometric reference. The simulator’s selected monitor and rendering configuration determines the final in-game value. Copy monitor measurements deliberately includes a Compute reminder rather than presenting a website angle as the game result.

Set Up Three Screens Without Mixing Up the Angles

The documented example assumes matching monitor model, size and resolution. Keep equal side angles and a centered eye for this assistant’s supported reference. If panels differ, distances are uneven or the viewpoint is offset, uncheck the matching-arrangement assumption and consult native setup help. No precise combined or game angle is substituted for that unsupported arrangement.

Why Three Projections Changes the Side-Angle Behavior

The dedicated triple guide says the flat side-angle field does not affect rendering while Render scene using 3 projections is disabled. Its enabled mode uses separate cameras for the screens. The checkbox here records a checklist confirmation; it neither changes physical geometry nor reads the game’s real setting.

Monitor the rendering choice in the simulator itself. The article also describes an NVIDIA-specific multi-projection performance option, but this site has not tested your hardware and predicts no frame-rate gain or cost. The physical center-panel angle, side joint angle and any multi-view render configuration remain different quantities.

What to Enter for Curved Monitors

Use the hardware’s published radius, in millimeters: 1500R describes a 1500 mm curvature radius. It is not a seating-distance prescription. Record how you measured curved outer width and check the native tooltip; the inspected text does not establish one universal arc-versus-chord convention for that field.

The dedicated triple article replaces flat side angle with Radius of curvature. The seating article also mentions an extra relative angle beyond the natural curve. Because those descriptions differ, the assistant shows an additional relative angle only when you confirm that your installed UI requests it. A cached flat side angle never appears in a curved copy record.

A curved physical reference requires visible horizontal surface arc width, height and the radius. Diagonal-only or straight-chord measurements are not quietly reused as arc length. With valid dimensions, the shared cylindrical model can describe the center panel; it does not recreate a three-curved-screen renderer or supply total native FOV.

Fix Your Horizon and Driver Height After FOV Setup

Global Horizon and View Height

Look straight ahead once monitor setup is complete. The seating guide identifies Shift + [ and Shift + ] for horizon placement, and Ctrl + [ and Ctrl + ] for global driver height. The Camera Tool reference also separates horizon and driver-view height from the camera’s FOV control. Change one part at a time so a position problem does not become an unexplained projection adjustment.

Per-Car Camera Position and Save Car

The seating guide describes entering and exiting the car, selecting Cockpit camera, opening Ctrl + F12 and adjusting X/Y/Z placement offsets before Save Car. The general Camera Tool page includes broader cockpit-save scope wording. Follow the described workflow, then verify which car or cars are affected in your installed build before relying on a per-car assumption. This website does not open, export or write camera files.

Check Your iRacing Setup Before Driving

Use the four-stage checklist above to separate measuring, entering settings, running Compute and aligning the view. Checkboxes are your own local confirmations, with no simulator synchronization. Reset checklist clears progress while leaving monitor measurements intact. Reloading resets progress; a shared link restores measurements and mode, not completed steps.

Before keeping a record, confirm outer versus visible width, one-edge versus total bezel, units, selected monitor type and the normal eye position. Recheck after moving hardware. Copy includes mode-specific fields and assumptions; a share link can also preserve an incomplete measurement record with its missing fields visible. Neither action confirms that the numbers were measured correctly.

Use Compare FOV conventions across racing games for game-input comparisons, or the general screen geometry calculator for broader physical relationships. The angle converter can change a known rectilinear angle’s axis; it does not replace iRacing’s native Compute workflow.

References were checked on November 18, 2026. Public guides are documentation evidence; the installed simulator build and the exact Compute algorithm have not been tested. This independent site has no iRacing endorsement or affiliation.

If Your View Still Looks Wrong

Why is the optional physical angle different from the native result?

Check visible versus outer width, selected monitor/rendering mode and units first. The center-panel reference does not reproduce all native projection behavior. Keep the game’s Compute result separate from the website’s physical angle.

Can a 27-inch diagonal fill Monitor Width?

No. It can estimate visible width using an aspect ratio, but the outer housing remains unknown. Enter a measured edge-to-edge width including frames. Imported visible measurements deliberately do not fill that field.

Should I enter one bezel or both?

The native triple article specifies one edge. The optional flat width helper subtracts two equal edge bezels only after you explicitly confirm that assumption. A measured gap between two displays can contain two frames plus empty space and is a different value.

Why is my flat side angle hidden for 3 Curved Screens?

The dedicated guide substitutes radius in that configuration. The assistant preserves your flat value for returning to flat mode, but excludes it from curved output. A separate optional relative angle is available only for an installed UI that requests it.

Should I change FOV to move the dashboard or horizon?

Check monitor measurements and Compute first, then use the documented horizon, height or camera-position controls for placement. Changing several settings together makes the cause harder to identify. No value here guarantees lap times, driving skill or visual comfort.

ANOTHER WAY TO LOOK AT IT